Verderflex Ds500 Software

Thank you very much for your interest. On this page you can find:

Display
Manifest
Software Upgrades

Please download what you need for your product.

*Warning* Updating from earlier version (01.00.26 or earlier) to this firmware version will instigate a Factory Reset returning all pump settings to factory default values.

To update the software on your Ds500 pump, please:

Download all files for the update, these will always be the Ds500 Manifest and Software version 01.00.28 files and sometimes the Ds500 Display files.
The downloads will start in a new window.
Copy all the files to a USB FAT32 flash drive, into the root directory.
Insert the USB flash drive into the USB slot in the back of the Ds500 unit.
Turn the pump off and on whilst holding the Stop button. This can also be performed through the menus on the pump if no power swich is local to the pump.
Release the Stop button when the LED flashes White.
Unit will reboot when the update is completed.
Confirm the pump is running the new software through the menus or on the boot screen.

Instructions to how to perform the software update are also in the Ds500 operating manual.

*Note: When the pump has successfully connected to the internet, there is now a pin code shown on the Wi-Fi Settings page. This pin code is to be entered when adding a pump to your Remote Assistant mobile application (Version 11 onwards). Each time the pump re-connects to the internet, it will receive a new pin code which is only required once, when adding the pump to your Remote Assistant account.

Previous Versions

V01.00.24
Download Here

Updates and New features
1. Add dynamic update of time in Date/Time Settings page.
2. Add settings restore icon UI button in Diagnostic page.
3. Enabled I2T safety protection on motor.
4. Allow to prime pump even when remote stop is active.
5. Reduce flow rate updates to EEPROM in 4-20mA mode.
6. Factory reset will be enforced at first run automatically.
7. Implement settings restore function.
8. Configure remote stop input pin settings based on user settings and add "Link Cable" option in Digital Output selection in I/O Settings page.
9. Factory reset will be enforced at first run automatically.
10. Implement settings restore automatically during firmware update.
11. Add WiFi setup prompt on startup after factory reset.
12. Implement WiFi module check at pump startup.
13. Implement changes in 4-20mA high level input handling.
14. Change 4-20mA output range for "Full Scale" mode.
15. Implement adaptive motor feedback position error limit.
16. Flash red LED quickly when display update has failed.
17. Enhance RTC driver to reduce read time error.
18. Improve contact pulse detection logic for more accurate timing.
19. Change ADC sampling time to give a more accurate 4-20mA input reading.
20. Implement logs upload to server via Device Update API.
21. Implement maximum speed option in pump settings.
22. Add boundary checking when setting maximum and current volume in fluid monitor page.
23. Show alert pop up when fluid recovery is unavailable when there is no input in 4-20mA mode.
24. Remove lower limit (10% of max speed) checking in setting 20mA scaling percentage.
25. Log to flash when default calibration offset has been applied.
26. Add "No Network" and "Scan Error" warning messages after a failed WiFi scanning.
27. Add "PIN Code" label in WiFi setup page when returned from server.
28. Change colours of the toggle switch.
29. Show error pop up in operating page when motor failure is recovered during splash page.
30. Flash red / white LEDs to indicate display update failure.
31. Do not allow user to start flow calibration while prime tube alert is still on screen.
32. Connect WiFi SSID with strongest signal strength.
33. Display pairing PIN code in WiFi setup page for multi-tenancy support.
34. Display WiFi setup prompt at startup if data reset to default because of settings version changed.
35. Add “Total Pump Runtime” element in WiFi payload.
Bug Fixes
1. Fix in updating flow rate to server when selection arrow is pressed in Operating page.
2. Fix flashing red LED when motor cable is disconnected at startup.
3. Fix current volume in fluid monitor page not restored after a power cycle.
4. Fix firmware update issue when hardware configuration EEPROM has not been programmed.
5. Fix WiFi scanning issue after factory reset and WiFi setup prompt being skipped.
6. Fix display corrupt issue after firmware update.
7. Fix prime active / inactive logging on diagnostic page.
8. Fix prime not working after flow rate changed by UP / DOWN arrow.
9. Fix and align pump length to 10 characters in settings and UI.
10. Fix issue in driver in reading motor registers.
11. Fix issue in exported diagnostic log on USB flash.

Ds500 Firmware

V01.00.24

Updates and New features